450 Chemical‑Industrial Vibratory Filter Machine

450 Chemical‑Industrial Vibratory Filter Machine

450 Chemical‑Industrial Vibratory Filter Machine | Paint, Resin & Slurry Filtration | Xianchen Meta Description: Henan Xianchen 450 chemical‑industrial vibratory filter machine for paint, PVC resin powder, detergent powder and industrial slurry filtration. 304 stainless‑steel build, low noise, fast screen change, ideal for small‑batch chemical processing.

  • Product Introduction

 

Product Overview

Our 450 Chemical‑Industrial Vibratory Filter Machine is specially developed by Henan Xianchen Intelligent Equipment Manufacturing Co., Ltd to solve solid‑liquid separation and impurity‑removal challenges within chemical‑production environments. Modified from the proven 450 vibratory filter platform, this model is optimized to handle corrosive, sticky and fine chemical raw materials. It is widely adopted for processing paint, resin powder, PVC resin powder, citric acid, polyethylene powder and laundry‑detergent powder. Besides chemical materials, it also delivers stable performance for paper‑industry media such as white clay slurry, coated starch, black liquor and pulp waste liquor.

Designed for small‑volume feeding and low‑impurity raw‑material batches, this industrial filter unit focuses on high filtration accuracy and operational stability. Different from general‑purpose screening equipment, it takes sticky chemical characteristics into consideration during structural design, effectively reducing screen blocking risk caused by high‑viscosity paint or agglomerated resin powder. It is a cost‑effective separation solution for fine‑chemical workshops, paint mixing rooms and pilot production lines.

Core Working Principle

This chemical‑grade filter adopts vertical vibrating motor as its vibration source. Eccentric hammers are installed on both upper and lower ends of the motor. When powered on, rotating eccentric hammers generate three‑dimensional excitation force including horizontal, vertical and inclined movement. Vibration energy passes through the receiving tray to screen frame and raw materials, realizing full grading and filtration of chemical powders and slurries.

Users can loosen the locking bolt to adjust the phase angle of the lower counterweight. Changing the phase angle modifies material movement trajectory and residence time on the screen surface. Operators can tune this parameter according to material viscosity, particle size and required throughput to reach optimal separation efficiency. Remember to fully tighten the locking bolt once adjustment finishes. Note that the upper counterweight angle is factory‑fixed and cannot be adjusted manually. Improper adjustment will lead to unstable material flow and poor filtering effect.

Key Specifications

 

Item Parameter
Motor Power 0.25 kW
Motor Speed 1440 r/min
Voltage 220 V / 380 V
Noise ≤50 dB
Max One‑time Feeding ≤5 kg
Amplitude ≤5 mm
Overall Dimension 550 × 500 × 620 mm
Total Weight 40 kg
Main Material 304 Stainless Steel

Main Advantages & Benefits

First of all, the whole machine contact part is made of 304 stainless steel, offering good anti‑corrosion performance against most ordinary chemical raw materials, avoiding metal contamination of finished chemical products. Secondly, the unit features low‑noise operation below 50 dB, which will not create heavy noise pollution inside closed chemical workshops.

Another core benefit is ultra‑fast screen replacement. Skilled operators can complete screen change within 3‑5 minutes with only one person, minimizing production downtime when switching mesh sizes for different chemical formulas. Compact size means the filter occupies little workshop floor space. There is no need for complex concrete foundation construction. Flexible counterweight adjustment supports diversified material processing needs, whether you process fine powder or thick industrial slurry.

Installation & Commissioning Guidance

Place the machine on a flat workbench. Lay shock‑absorbing rubber mats between machine base and workbench surface to isolate vibration. Since internal motor cables sustain continuous strong vibration during operation, standard grounding wire connection is required strictly for site safety in chemical workshops.

Before feeding chemical raw materials, perform a 20‑30 minutes no‑load trial run. Confirm the motor rotates clockwise. If rotation direction is reversed, adjust three‑phase power supply wiring. Under low‑temperature workshop conditions, starting current will be slightly higher, and it should drop back to rated current after 20‑30 minutes running.

Pay close attention to abnormal noise during trial run. Loose fasteners caused by transportation and reassembly are the major trigger for strange noise. During startup and shutdown, the machine will pass through a short resonance zone which lasts about 13 seconds. Temporary increase of amplitude and noise in this period belongs to normal mechanical phenomenon, not equipment failure. After idle inspection passes, feed chemical materials in small quantity gradually, and increase feeding volume to target capacity while fine‑tuning counterweight position for best filtration output.

Screen‑Replacement Operation

Remove upper frame and lower frame with screen facing upward.

Loosen and take down two tensioning bolts on the screen frame.

Lay new screen flat on the frame surface.

Tighten one tensioning bolt, fold screen edge onto the other bolt position, and tighten bolts firmly.

Cut redundant screen fabric around frame with scissors.

Critical reminder: tensioning bolts must be tightened as much as possible. Loose screen will cause slurry leakage and premature screen damage under sticky chemical‑material working conditions.

Troubleshooting & Wearing Parts

Common Fault 1: Motor runs abnormally or refuses to start

‑ Check power supply for phase loss or circuit break; ‑ Inspect socket contact condition; ‑ Confirm whether motor coil is burnt out; ‑ Check excessive lubricating‑oil filling or severe bearing wear.

Common Fault 2: Abnormal operating noise

‑ Verify whether machine base is stable; reinforce base when excitation force causes violent shaking; ‑ Check for broken springs; ‑ Inspect whether motor mounting bolts get loose or damaged; ‑ Make sure machine body does not collide with surrounding workshop objects.

Vulnerable spare parts for regular stock‑up

Bearings, sealing rings, sieve mesh. In chemical‑production environment, aging sealing rings may lead to slurry leakage. Damaged sieve mesh will allow oversized particles to flow into finished products. Regular inspection and timely replacement are required.

Application Scenarios

This chemical‑industrial filter fits paint workshops, resin processing workshops, detergent production lines, fine‑chemical pilot labs, as well as paper‑making factories. It handles paint, resin powder, PVC resin powder, polyethylene powder, citric acid, laundry‑detergent powder, white clay slurry, black liquor and pulp waste liquor. It is suitable for small‑batch production and laboratory sample‑filtering work.

Conclusion

If you are looking for compact, low‑cost vibratory filtration equipment for chemical and paper‑industry small‑batch processing, the 450 Chemical‑Industrial Vibratory Filter Machine will be your reliable option. It combines small footprint, easy maintenance and adjustable screening performance. With simple installation and fast screen‑change design, it can help you remove impurities efficiently and improve final product quality.

Hot Tags: 450 chemical‑industrial vibratory filter machine, China 450 chemical‑industrial vibratory filter machine suppliers, factory, Airflow Sieve, material screening equipment, Plane Gyratory Screen, Rotary Drum Screen, sieve screening, vibratory screeners

Send Inquiry

(0/10)

clearall